CladisticsATE-VXI-PXI Battery-Solar-Cell Calibration Component-Testing Computers d Dashboard-Instruments Data-Acquisition Electrical-Safety Electronic-Loads Engineering-Services Environmental-Instruments High-Energy-Power HVAC Instrument-Marketing Insulation-Testers LCR-Meter Life-Sciences Logic-Analyzers Mass-Spectrometer Medical-Diagnostic-Instruments Metrology MicroOhmmeter Multimeter-DMM Optical Spectroscopy Oscilloscopes pH-Conductivity Photonics-Optics Power-Supplies Research-Instruments Scientific-Instruments Signal-Generator Spectroscopy Spectrum-Analyzers Substance-Analysers Waveform-Function-Generators
The 10A Micro-Ohmmeter Model 6240 is a rugged, low resistance tester designed for both plant maintenance and field use. Utilizing a four-lead Kelvin method of testing, the Model 6240 Micro-Ohmmeter accurately measures very low resistance within 0.25%.
Resistance measurements are automatically calculated from 1µΩ to 400Ω with resolutions down to 1µΩ. The Model 6240 has selectable test currents of 10A, 1A, 100mA and 10mA and includes a polarity reversal function.
Operator safety by automatic discharge of residual charge on the equipment under test.
4-Wire measurement with automatic compensation of undesirable voltages and lead resistance.
- Measures from 1µΩ to 400Ω
- Test current selection from 10mA to 10A
- Manual temperature compensation
- Front panel polarity reverse function
- Stores up to 99 test results
- Auto store of multiple test results
The DataView Software included allows you to configure the instrument, temperature compensate the test results, as well as, store data and print reports.
This meter from Extech goes upto 1000A Clamp Meter. An AC/DC True RMS DMM with IR Thermometer and Bluetooth MeterLink.
MultiMeter functions include AC/DC Voltage, Resistance, Capacitance, Frequency, Diode, and Continuity.
- True RMS Current and Voltage measurements
- 4000 count backlit display
- Peak hold captures inrush currents and Transients
- Built-in non-contact IR Thermometer with laser pointer
- Features include Data Hold and Min/Max and Auto Power off
- Autoranging with manual range button
MeterLink Bluetooth transmitter Wirelessly transmits Voltage and Current readings to selected FLIR thermal imaging IR cameras to incorporate meter readings with thermal images
The EX845 METERLiNK for Android app allows the user of an Extech Instruments EX845 clamp meter to remotely view and display readings from the meter on an Android phone or tablet up to 10m or 30 feet away.
This includes the display of readings for the following functions: ACV, DCV, ACA, DCA, capacitance, resistance, frequency, diode test, Temperature (both contact, Type-K probe and non-contact, infrared functions). Function indicators highlight which measurement mode is selected on the meter. Additionally, Data Hold and Min/Max functions are also remotely displayed.
Hot-line state detection – Protects Meter on accidental voltage in Part/equipment on Test. (>30V). Large bolt mark – A large (lightning) bolt mark is with a buzzer sound, when HV is applied.
- Automatic data hold
- Bargraph just like analog meter
- Large display with backlight
- Current 1.2mA @1000V/1M
- Short Circuit Current <2mA
- 250V – 500V – 1000V Test V
- Max Resistance 4 G Ohms
Rich with original functions, like the whole SCOPIX range, the OX 7062 dual-channel 60 MHz digital oscilloscope, a “multi-instrument” with a minimum footprint, provides outstanding performance, thanks in particular to its 12-bit / 2.5 GS/s converter.
The multi-channel TRMS digital MULTIMETER – 8,000 counts, 200 kHz – measures amplitudes, resistances, continuity, capacitances, frequencies and temperatures, and performs tests on components. It includes a recorder with windows from 5 min to 24 hours.
This App enables you to view live waveforms, perform measurements and analyses, capture instrument screenshots and control METRIX oscilloscopes from your tablet or phone.
This can be used with these Instruments – OX7000, OX6000B or MTX105X METRIX oscilloscope series with an Ethernet connection. The application provides total control over the oscilloscope such as viewing measurements and starting/stopping acquisitions.
ScopeNet can be used to view all the instruments and their compatibility on the network . All functions and modes installed are available with ScopeNet.
This is from Chauvin Arnoux a French group marketing professional measurement instrumentation.
Measure volts, ohms and amps with a basic V DC accuracy of 0.015%. DC leakage current measurements and frequency measurements too.
The RS-232 port on the back panel can be used to connect to your PC. A USB to RS-232 interface adapter cable is included standard with the DMM4020 for connecting to your PC’s USB port.
The limit compare mode provides pass/fail indicators to quickly show if a test passes or fails to help eliminate mistakes, especially for results that are close to the limit.
5.5 digit resolution Measure volts, ohms and amps with a basic V dc accuracy of 0.015%. Frequency measurements Save cost and bench space by replacing a multifunction DMM and counter with one instrument.
DC leakage current measurements Make sensitive low current measurements with 1 nA resolution. Dual display Measure two different parameters of the same signal from one test connection. PC Connectivity Easily connect to a personal computer using RS-232 or USB.
From – Tektronix
With fast sampling on each channel and 10 Mpts/Ch memory the WaveSurfer MXs is an outstanding choice from 200 MHz to 1 GHz. Along with class leading specs, the WaveSurfer MXs includes a number of unique tools that simplify how you use an oscilloscope and how you perform everyday debug and validation.
- – 200 MHz to 1 Ghz Bandwidth
- – Up to 5 GS/s
- – Big 10.4″ LCD Display
- – Small 6″ footprint
- – Powerful SMART Triggers
- – 10 Mpts/ch memory
- – LabNotebook Report Generation
Complete I2C, SPI, UART, RS-232, LIN, and CAN serial triggering, including powerful conditional data triggering, allows quick and easy isolation of specific events on your embedded controller.
LeCroy is a leading provider of oscilloscopes, protocol analyzers and related test and measurement solutions that enable companies across a wide range of industries to design and test electronic devices of all types. Estd. 1964.
“The acquired company will now be included in Teledyne’s Instrumentation segment and operate under the name Teledyne LeCroy, Inc…”
700 Chestnut Ridge Road Chestnut Ridge, NY 10977-6499
Updated Aug 14
The SR715 LCR Meter and SR720 LCR Meter measure passive components with as little as 0.05 % error. These easy-to-use instruments are quick to setup, adjust and calibrate.
The SR715 and SR720 are ideal for applications such as incoming inspection, quality control, automated test, and general benchtop use.
SR715 and SR720 have built-in features to aid in component sorting. This is especially useful for production testing, incoming inspection, device matching, or when you need to test multiple devices of similar value. The meters allow you to sort components into as many as ten different bins.
- 0.05 % basic accuracy (SR720), 0.2 % (SR715)
- 5-digit display of L, C, R and Q or D
- Test frequencies to 100 kHz (SR720)
- Up to 20 measurements per second
- Binning and limits for parts sorting
- External capacitor bias up to 40 V
- RS-232, GPIB and Parts handler interfaces
Scientific Instruments, Vacuum & Analytical Instruments, Time & Frequency Instruments. Test & Measurement for Research and Analysis